Check three Ledyard zoning rules before anyone prices a layout
Ledyard's solar rules sit in §8.32 of the Ledyard Zoning Regulations, in the version amended through July 16, 2026. Three parts of that section can take a roof face, a patch of yard or an equipment spot off the plan. Check all three before you compare bids, because a bid drawn on ground the town won't allow is not a real price.
1. The Development District rule. In the Gales Ferry Development District (GFDD) and the Ledyard Center Development District (LCDD), ground-mounted accessory arrays are prohibited, and roof panels are not permitted on front-facing roofs.
A zoning district is the legal zone shown for your lot on the town's Zoning Map. It is not the village name in your mailing address. Under §3.2, both development districts are non-residential zones, so a house with a Gales Ferry address can sit in a residential zone where this rule does not apply. Ask the town to confirm the district for your parcel. On a corner lot, also ask which roof counts as "front facing". We found no published definition.
2. The septic rule. No solar equipment may sit over a septic system, a leach field or an identified reserve area unless Ledge Light Health District (LLHD) or CT DEEP approves it. A reserve area is ground set aside for a future replacement leach field. It may also be the sunny patch of lawn you had in mind for a ground mount.
3. The floodplain rule. If the parcel is in a FEMA floodplain or an area of known localized flooding, "all panels, electrical wiring, automatic transfer switches, inverters, etc." must sit above the base flood elevation (BFE). BFE is the flood height the FEMA map sets for your location. Ledyard's flood protection section (§12.2) applies to FEMA Zones A and AE, and the town's Zoning Official interprets where those boundaries fall. The rule names inverters and transfer switches, so it reaches backup equipment as well as panels.
| Check | What it can take off the plan | Who confirms it |
|---|---|---|
| District (GFDD or LCDD) | Front-facing roof faces, any ground mount | Ledyard Land Use office, from the Zoning Map |
| Septic, leach field, reserve area | Spots over the system | Ledge Light Health District (or CT DEEP) |
| Flood zone (FEMA A or AE, or known local flooding) | Equipment spots below the BFE, such as a low basement | Ledyard Zoning Official, using the FEMA map |
Outside those limits, §8.32(C) allows accessory solar on a roof or on the ground in all zones. Ground arrays have their own limits: none in the front yard, side and rear arrays must respect the zone's setbacks, the array may cover no more than 40% of the side and rear yards combined, and freestanding structures may be no taller than 15 feet.
To check your parcel, open the town GIS map from the Ledyard Land Use page and look up your address in the FEMA Flood Map Service Center. Then ask Land Use to confirm what you found. If the house sits in a local historic district, such as the small Sawmill Historic District around the town-owned Up-Down Sawmill, also ask the Ledyard Historic District Commission whether panels need its review.
What the proposed two-quote service would hand you
Proposed service. New London Solar is a proposed solar service for New London-area homeowners. Coverage of Ledyard is proposed and not yet confirmed.
The assessment would cover 12 months of your electricity use, roof faces and shade, your main panel, the circuits you want in an outage, and where a battery could go (illustrative example: about two hours on site). You would receive:
- Quote A, solar only. A drawing of the layout §8.32 allows on your parcel, the panel count, the system size in DC kW, module and inverter models, an annual kWh estimate with shade assumptions written out, the total price and the price per DC watt.
- Quote B, backup for selected circuits (optional, priced separately). The circuits you choose, battery size and power, equipment location against the BFE, and the storage-program reserve setting (all explained below).
- Circuit map and responsibility sheet. Your panel schedule with backed-up circuits marked, and a named owner for each permit, sign-off and utility filing.
Ledyard gives two reasons to keep the quotes apart. A battery folded into the solar price breaks the price-per-watt check in the worked example below. And the floodplain rule can push backup equipment up a floor, which changes Quote B's cost without touching Quote A. See how the two-quote service would work.
Ledyard's permit order: zoning first, then building
Under §3.6 of the zoning regulations, nothing is erected or altered until the Zoning Enforcement Officer or the Planning and Zoning Commission issues a zoning permit, and the Building Official issues a building permit, "in most instances" with LLHD approval.
The building permit application asks for proof of approval from Planning and Zoning, LLHD and the Inland Wetlands and Watercourses Commission (IWWC), as each applies, plus the contractor's license and insurance. Incomplete applications are denied after 30 days, and fees are non-refundable. Filing for a building permit before zoning is settled puts that fee at risk. The order:
- Confirm the parcel: district, flood zone, septic location.
- Get LLHD approval if the layout touches septic ground. We found no published LLHD process for this, so ask LLHD who handles it.
- File the zoning permit. The Ledyard zoning permit application asks for the zoning district, map, block and lot, the flood zone, any Planning and Zoning or IWWC permit number, whether the land is owned by the Mashantucket Pequot Tribe (with a tribal letter if so), and any deed restrictions or covenants that may conflict. It needs a plot plan showing the well, septic, wetlands and setbacks.
- File the building permit, and the electrical permit if required, with the approvals attached.
- Apply to Eversource for interconnection. This is a separate application from the town permits.
At the Ledyard Building Department, forms can be filled out online, but completed forms and the fee still go in person to Town Hall at 741 Colonel Ledyard Highway, Monday to Thursday. Building and trade permits cost $15 per $1,000 of estimated value or part of $1,000, including the state's $0.26 per $1,000.
Ask the Land Use office two things
- For a rooftop array on a house in a residential zone (R20, R40 or R60), is this a staff zoning permit or a Commission site plan approval? The use table lists accessory solar as site plan approval under "non-residential accessory" uses, while residential accessory structures get a staff permit. §8.32(A) also says solar systems must meet the site plan requirements on the Appendix B check sheet and the bulk requirements of the zone. Ask which route applies to your house, whether you need that check sheet, and how long the review takes.
- Will solar be billed as a building permit, an electrical permit, or both on the same value? The $15 per $1,000 rule covers both, so the answer could double that line in a quote.
Worked example: the front-roof bar, priced per watt
The district below is assumed for illustration. Yours comes from the town, not your village name.
Illustrative example: a hip-roof house in the Gales Ferry Development District whose street side faces south.
- Layout 1, south (front), east and west faces: 26 panels × 400 W = 10.4 kW DC (illustrative). Not permitted, because §8.32(A) bars panels on front-facing roofs in GFDD.
- Layout 2, east and west faces only: 16 panels × 400 W = 6.4 kW DC (illustrative). EcoGen's statewide production reference is 1,294 kWh per kW a year, so 6.4 × 1,294 ≈ 8,280 kWh a year before shade (illustrative calculation). Treat that as a rough starting point. It is a statewide figure, and east- and west-facing panels usually produce less than south-facing ones. The bidder's estimate for these faces, with shade written out, replaces it.
- Quote A, solar only, illustrative price $18,560. $18,560 ÷ 6,400 W = $2.90 per watt (illustrative calculation).
- State benchmark: EcoGen's Connecticut index of $2.80/W, a modeled installed price before incentives (September 2026 Edition, prices as of Sept. 25, 2026). EcoGen puts typical written quotes at $2.46 to $3.14 per watt in Connecticut (state benchmark).
- Reading: $2.90 is inside the band, about 3.6% above the benchmark.
- Ledyard permit fee, illustrative calculation: $18,560 is 18 full thousands plus part of a 19th, so 19 × $15 = $285, state fee included. Whether that is charged once or twice (building and electrical) is unknown. Ask the Building Department.
| Layout (illustrative) | Roof faces | Panels | DC kW | kWh a year before shade | Allowed in GFDD? |
|---|---|---|---|---|---|
| Layout 1 | South (front), east, west | 26 × 400 W | 10.4 | Not estimated | No, front-facing roof |
| Layout 2 | East and west only | 16 × 400 W | 6.4 | About 8,280 | Yes, subject to the other checks |
In this example the bar removes the best-placed face, not a marginal one. A bidder who drew Layout 1 priced a system the town would reject, so have it redrawn before you compare prices. In the development districts the zoning use table also lists accessory solar under site plan approval by the Commission, so ask Land Use how long that review takes before you agree to an install date.
Then compare by price per watt. DC watts are the panels' combined rated output (panel count times panel wattage), so $/W lets you compare a 6.4 kW bid with a larger one. The benchmark is a state figure, not a Ledyard price or a quote. Use it to spot a bid that needs explaining. Roof work, a panel upgrade or a battery inside the price all push $/W up, so each belongs on its own line.
Price backup separately, for the circuits you pick
Backup has its own sizing and its own Ledyard rule, so keep it out of the solar price. EcoGen models a 13.5 kWh battery at $13,500, a planning figure of $1,000 per kWh, not a quote. Fold that into one total and the same example reads $32,060 ÷ 6,400 W = $5.01 per watt (illustrative calculation). That looks far out of range only because battery dollars were divided by panel watts.
Size it from a critical-loads list
A critical-loads list is the short list of circuits you want running in an outage. The state's storage fact sheet sizes a battery from three questions: what to power, where the battery can go, and how long it must run without recharging. If your house has a well pump, a sump pump or a boiler, give each its own line. Then ask for three numbers:
- Usable kWh: the energy the battery can deliver, which sets how long the list runs.
- Continuous kW: the power it supplies at once, which sets how many circuits run together.
- Surge kW: the short burst that starts a motor such as a well pump. Too little, and the pump may not start.
Quote B should also say what stays off and give runtime under stated assumptions, with and without solar recharge.
Flood-zone equipment goes above the BFE
In a flood zone, §8.32(A) puts the inverter, transfer switch and wiring above the BFE, so a basement location may be ruled out. Quote B must state where the battery, inverter and transfer switch mount relative to the BFE, and the cable route to your panel. Any extra cost for mounting higher belongs in Quote B, not in Quote A.
ESS events and your outage reserve
Eversource customers can enroll a battery in Energy Storage Solutions (ESS). For applications from April 1, 2026, made through an Eligible Contractor, the program pays $30 per kWh upfront for a standard residential customer ($130 in Grid Edge areas). It then pays $300 per kW a year for 10 years ($450 underserved, $550 low-income), twice a year, based on the average kW (AC) the battery delivers during events. Expect about 50 summer and 5 winter events. Earnings depend on how fast solar recharges the battery and how often you opt out.
Illustrative calculation: a 13.5 kWh battery earns $405 upfront, or $1,755 at the Grid Edge rate. An average 5 kW event contribution would earn $1,500 a year; actual performance sets the amount.
Those events draw on the same battery you want for outages. The reserve setting is the share of the battery held back for your own use. A higher reserve keeps more backup ready and leaves less to deliver in events, so Quote B must state the reserve its payment estimate assumes. Ask too whether your address is in a Grid Edge area.
Eversource rules that change the money in 2026
Ledyard, including Gales Ferry, is Eversource territory. The Connecticut Office of Consumer Counsel lists town-provided electric service only in Bozrah, Groton, Jewett City, Norwich, South Norwalk and Wallingford, and Eversource owns the Gales Ferry Substation on Whalehead Road. Check your bill anyway. This page does not cover Mashantucket Pequot tribal land.
One Ledyard wrinkle: the town's zoning regulations mention Groton Utilities only for water-supply approvals. If a Groton Utilities bill reaches your house, check whether it is for water or electricity, because the electric bill decides which solar rules apply. Next door, parts of Groton buy power from Groton Utilities, outside the state's residential solar tariff and ESS.
Eversource solar customers enroll in the Residential Renewable Energy Solutions (RRES) program and pick one of two payment methods. Figures apply to applications in 2026, under the PURA Year 5 RRES decision.
| Netting | Buy-All | |
|---|---|---|
| How you're paid | Exported power is credited at the full retail rate on your bill | Every kWh the panels make is paid at a fixed rate |
| 2026 rate | Retail credit, minus a Solar Energy Adjustment of $0.0402 per kWh on all production | $0.3289 per kWh |
Both options cap systems at 25 kW. You elect at interconnection and keep the choice for 20 years. Ask every bidder to show first-year value under both, using your own 12 months of usage and the layout that survives §8.32, not a larger one the town would refuse. Then have the election written into the quote.
Rates for 2027 were not set as of November 18, 2026. Public Act 26-127 extends RRES through December 31, 2028, or earlier if PURA launches a successor. Ask whether a bid includes Eversource's $163 application and $230 meter fees (EcoGen's figures).
Older guides still quote a quarterly certificate payment under Netting or an ESS rebate of up to $16,000. Neither is current. The federal Residential Clean Energy Credit (§25D) is not available for property placed in service after December 31, 2025. A bid that still subtracts a federal credit from a homeowner-owned system is using old math.
Who may install, and who files what
Can you install your own panels in Connecticut? The electrical side is licensed work. The Department of Consumer Protection places solar electrical work under a PV-1 or an E-1/E-2 license, and contractors also need Home Improvement Contractor (HIC) registration. Ledyard's building application asks for the contractor's license and insurance. If you plan to do part of the work yourself, ask the Building Department what it accepts from a homeowner before you buy anything.
For bidders, run three checks:
- License and registration. Look up each bidder's PV-1 or E-1/E-2 number and HIC registration, including any service proposed on this site.
- Installs or brokers? Some companies sell the job and pass it to another installer. Ask whose crew and whose license go on the Ledyard application.
- Who files what. Get every filing in writing with a name beside it. Under Ledyard's 30-day denial rule, a missing attachment costs you.
Line up every bid on the same fields
A bid that ignores your district, or mixes the battery into the solar price, can't be compared with one that doesn't. Ask every bidder to fill in the same fields.
| Field | Quote A: solar only | Quote B: backup (optional) |
|---|---|---|
| Fits the confirmed district and septic plan | Yes or no, with drawing | n/a |
| System size | DC kW, panel count, module model | Usable kWh, continuous kW, surge kW |
| Production or runtime | Annual kWh, shade assumptions written out | Runtime for the critical-loads list, assumptions stated |
| Price | Total and $ per DC watt | Total, on its own line |
| Location | Roof faces used | Battery, inverter and transfer switch vs BFE |
| Utility terms | RRES election (Netting or Buy-All) | ESS enrollment, reserve setting, Grid Edge status |
| Paperwork | Who files zoning, building, electrical, Eversource | Who files ESS and any added electrical permit |
In Ledyard, two rows carry the most weight. The district row tells you whether a bid is real. The location row tells you whether backup survives the floodplain rule. A bid with either row blank isn't finished.
Ledyard quote checklist: questions before you sign
Take these to every bidder, and use the quote checklist on this site to keep answers side by side.
- District. Has the town confirmed my zoning district? If GFDD or LCDD, does the layout skip every front-facing roof (as the zoning official reads my lot) and use no ground mount?
- Septic. Does anything sit over the septic system, leach field or reserve area? If so, where is the LLHD or CT DEEP approval?
- Flood zone. Is the parcel in FEMA Zone A or AE, or an area of known localized flooding? Where do the inverter, battery and transfer switch mount relative to the BFE?
- Zoning route and fee. Did Land Use say staff permit or Commission site plan approval, and does it want the Appendix B check sheet? Will Ledyard charge building, electrical or both, and is that in the price?
- Solar-only $/W. What is Quote A divided by DC watts, with no battery, roof work or panel upgrade inside? Where does it land against the state band?
- Separate Quote B. Is backup quoted on its own, with the critical-loads list, usable kWh, continuous kW, surge kW, stated runtime and the ESS reserve setting? Are you an ESS Eligible Contractor?
- Paperwork. Who files zoning, building and electrical permits, any LLHD sign-off, the Eversource application and ESS enrollment?
- License. What are your PV-1 or E-1/E-2 and HIC numbers, and do you install or broker the job?
- Tariff. Is the Netting or Buy-All election in the quote, with first-year value for both on the allowed layout, and what happens if enrollment slips into 2027?
- Door-to-door. From February 15, 2027, residential solar and storage sellers may solicit in person only between 9 a.m. and 7 p.m. A knock outside those hours is a reason to slow down.
Start with Ledyard Land Use: district, flood zone, septic. Then ask for Quote A on the layout that survives, and decide on Quote B once you know where the equipment may go.